Gold 2.0Si

Eddie nuff · Post by **Eddie nuff** » Sat Sep 14, 2013 5:19 pm

Vince wrote:I couldn't agree more. ..It's a stunning machine. ..especially on those wheel trims. ..the ones Paul loves so much ha ha

Those are Paul's wheel trims - couldn't give them to me quick enough.

Eddie nuff · Post by **Eddie nuff** » Sat Sep 14, 2013 5:21 pm

Dieselman wrote:Looking good there Neil, but riding too high at the front.

Agreed Will. There was a post on here about how to do it - someone point me in the right direction.

Eddie nuff · Post by **Eddie nuff** » Sat Sep 14, 2013 5:22 pm

Is that the white one that the guy dragged out of the salvage yard because it a little dent on the OSR?

Post by **citroenxm** » Sat Sep 14, 2013 5:28 pm

Oooerrr Neil.. Care But your a clever bloke.

FIRSTLY! MOST IMPORTANTLY you need a GOOD set of ramps!!

Get the front up on the ramps.. then put the car on the lowest. BE SURE you be safe under the car when its on the ramps and your under there so if she comes down... you be SAFE..

Have the car running and on normal height setting.. Slide yourself under the car equipt with an 11mm Socket and ratchet and extension..

Locate the anti roll bar running along the back of the subframe, on it theres a metal Clamp with a ROD attached to it or near it.. I THINK its near the middle of the bar.. You need to undo the clamp nut and rotate the clamp SLIGHTLY! one way and wait. Im not 100% sure which way make the car go up or down. If your adjustment one way for example makes her go down then obviosuly rotate the other way..

Remember to give her a few moments to adjust the height after each clamp movement...

Post by **russ92xmsed** » Sat Sep 14, 2013 5:44 pm

Eddie nuff wrote:Is that the white one that the guy dragged out of the salvage yard because it a little dent on the OSR?

I believe it is Neil, right place right time on that one. Too much white though...I like them with black trim.

So that's how you adjust the ride height. Scary!

Post by **Dieselman** » Sat Sep 14, 2013 8:41 pm

That is the car that Richard saved from scrap. It was a Cat-C write off due to reversing into a post. He bought a lamp cluster and bumper at CXM, just needs a spoiler now and some paint.

To set the ride height the easiest way is to loosen the clamp then manually operate the height corrector with a socket extension, when correct tighten the clamp.

Eddie nuff · Post by **Eddie nuff** » Sun Sep 15, 2013 7:31 pm

citroenxm wrote:FIRSTLY! MOST IMPORTANTLY you need a GOOD set of ramps!!

How about a pit? Got to be easier.

I'll have a crack at that then I can have a real good look at the rear subframe, wheel carrier etc at the same time.

Duke · Post by **Duke** » Sun Sep 15, 2013 7:38 pm

Glad the white V6 was saved, was a cracking car back in August 2012 when it was here...

Post by **citroenxm** » Sun Sep 15, 2013 7:50 pm

Eddie nuff wrote:
citroenxm wrote:FIRSTLY! MOST IMPORTANTLY you need a GOOD set of ramps!!
How about a pit? Got to be easier.

I'll have a crack at that then I can have a real good look at the rear subframe, wheel carrier etc at the same time.

Either Neil. The point was to be sure that any accidental LOWERING of the suspension will not harm you at all!

XMs are rather heavy things to rest on yur chest...

Citroen XM Forum

Gold 2.0Si

Re: Gold 2.0Si

Re: Gold 2.0Si

Re:

Re: Gold 2.0Si

Re: Gold 2.0Si

Re: